Clearfil SE Bond

01/01/2007 - "The materials used were Rely X ARC and Perma Cem, two one-bottle bonding agents (Single Bond, Bond-1) and one self-etching bonding agent (Clearfil SE Bond). "
07/01/2003 - "After applying either 40% phosphoric acid gel (K-etch, Kuraray Co) or a self-etching primer adhesive system (Clearfil SE Bond, Kuraray Co), sealant materials of two viscosities were applied (Teethmate F-1 and Protect-Liner-F, Kuraray Co) and cured with halogen (Optilux 500, Demetron) or plasma arc (Apollo-95E, Dental & Medical Diagnostic Systems, Ltd) curing units. "
05/01/2004 - "This study evaluated the temperature rise in two different adhesive (Clearfil SE Bond [CSEB] and EBS-Multi [EBSM]) and composite systems (Clearfil AP-X [CAPX,] Pertac II [PII]) by the same manufacturer when illuminated by four different light sources: Light-emitting diode (LED), Plasma arc curing (PAC), high intensity quartz tungsten halogen (HQTH) and quartz tungsten halogen (QTH). "
09/01/2014 - "Three self-adhesive luting agents (RelyX Unicem [UN], RelyX U100 [UC], and Clearfil SA Luting [SA]) and three conventional luting agents (Rely X ARC [RX], Panavia F [PF], and a two-step self-etching adhesive system [Clearfil SE Bond] associated with Panavia F [PS]) were evaluated. "
04/01/2004 - "Composite cylinders (2.9 mm x 3.0 mm) were bonded to airborne-particle-abraded intaglio surfaces of Procera AllZirkon specimens (n=80) with either Panavia F (PAN) or Rely X ARC (REL) resin luting agents after pretreatment with Clearfil SE Bond/ Porcelain Bond Activator (Group SE). "

10/01/2017 - "This laboratory study showed that the enamel bond fatigue durability of universal adhesives was lower than Clearfil SE Bond and Clearfil SE Bond 2, similar to Optibond XTR, and was not influenced by type of adhesive, unlike two-step self-etch adhesives."
08/29/2022 - "For adhesives in self-etch mode, the enamel fatigue bond strengths of Clearfil SE Bond 2 and G2-Bond Universal were significantly higher than that of the Scotchbond Universal Plus Adhesive, and the dentin fatigue bond strength of G2-Bond Universal was significantly higher than Clearfil SE Bond 2 and the Scotchbond Universal Plus Adhesive. "
10/01/2017 - "The shear fatigue strengths of universal adhesives to enamel in self-etch mode were significantly lower than that of Clearfil SE Bond and Clearfil SE Bond 2, but similar to that OptiBond XTR. "
06/01/2007 - "To evaluate the marginal adaptation of mixed Class V cavities restored with Clearfil Protect Bond (Kuraray), Clearfil SE Bond (Kuraray), and two experimental combinations of both marketed adhesives, after fatigue and water storage. "
08/01/2007 - "In contrast to Admira Bond and Clearfil SE Bond, fatigue loading resulted in a significant reduction of the bond strength for Hybrid Bond when compared to the unloaded restorations."

01/01/2007 - "In the two remaining groups, the smear layer was left intact, and the two resins cements were used in combination with the self-etching bonding agent (Clearfil SE Bond). "
10/01/2004 - "To evaluate the microtensile bond strength (MTBS) of a resin-based composite to smear layer-covered dentin using a self-etching primer, Clearfil SE Bond (CSEB), under two different hydration states. "
02/01/2022 - "This study evaluated the effects of different smear layer preparations on the dentin permeability and microtensile bond strength (µTBS) of 2 self-etching adhesives (Clearfil SE Bond [CSE] and Clearfil Tri-S Bond Universal [CTS]) under dynamic pulpal pressure. "
11/30/2018 - "The purpose of this study was to evaluate the effect of surface roughness and smear layer on the micro-shear bond strength (µSBS) of two self-etching adhesives, Clearfil SE Bond (SE) and Clearfil Tri-S Bond (S3). "
08/01/2007 - "Therefore, the smear layer from diamond burs had a greater influence in decreasing microTBS of Clearfil SE Bond that has the weakest acidity self-etching adhesive systems evaluated."

04/01/2006 - "The result of the FEM study of adhesive fracture tooth indicated that the stress distribution was similar to the normal tooth, Clearfil SE Bond was better than Super Bond C & B. "

01/01/2019 - "To apply titanium tetrafluoride (TiF4) in an aqueous solution or incorporated into the primer of a self-etching adhesive (Clearfil SE Bond) as dentin pre-treatment and evaluate its antimicrobial effect, determine the minimum bactericidal concentraion (MBC) against Streptococcus mutans and Lactobacillus casei and analyse its potential to inhibit the development of carious lesions at the restoration interface. "
02/01/2010 - "Teeth with deep carious lesions without signs and symptoms of irreversible pulpitis were divided by random allocation into two groups, according to the capping material utilized over demineralized dentin: experimental group (1): self-etching adhesive system (Clearfil SE Bond); and control group (2): calcium hydroxide liner (Dycal). "
02/01/2018 - "Investigate the effects of dentin pretreatment with 2.5% titanium tetrafluoride (TiF4) aqueous solution followed by two-step self-etching (CLE/Clearfil SE Bond) and one-step self-etching adhesive systems (SBU/Single Bond Universal) on carious lesion inhibition at the tooth-restoration interface using an in situ model. "