single bond

11/01/2019 - "After endodontic filling, 40 teeth were divided into five groups according to adhesive cementation: Adper Single Bond 2 + RelyX ARC, Excite DSC + RelyX ARC (EXC), Adper SE Plus + RelyX ARC (SEP), RelyX Unicem, and Set. "
02/01/2008 - "The posts were cemented with Adper Single Bond/Rely X ARC and stored in distilled water at 37 degrees C for 7 days. "
01/01/2005 - "The indirect restorations were subsequently cemented with Single Bond and Rely-X ARC. "
06/01/2004 - "180 vertical slot cavities were prepared in bovine teeth and filled with Z250/Single Bond system, for the following six groups (n=30): Soft-start I - 10 seconds at 75 mW/cm2 + 30 seconds at 560 mW/cm2; Soft-start II - 10 seconds at 190 mW/cm2 + 30 seconds at 560 mW/cm2; Pulse delay - 3 seconds at 300 mW/cm2 + 5 minutes waiting + 30 seconds at 560 mW/cm2; Plasma arc - 3 seconds at 1,500 mW/cm2; High intensity - 40 seconds at 810 mW/cm2; Conventional (control) - 40 seconds at 560 mW/cm2. "
05/01/2003 - "For Single Bond/Rely X ARC and Fuji Plus a significant decrease in bond strength was observed in dentin closer to the apex of the root. "

04/22/2015 - "Here we study the stability and rupture of molecular junctions under high voltage bias at the single molecule/single bond level using the scanning tunneling microscope-based break-junction technique. "
07/11/2023 - "Statistical methods were also used to determine the number of single-bond ruptures and the force of a single bond. "
07/04/2016 - "The forces varied widely at different ramps from close to 0 pN to 860 pN due to nonspecific adhesions and to the inherent inconsistency of single bond rupture. "
08/01/2015 - "Single unbinding events observed at higher surface delays were modeled according to the wormlike chain model, obtaining molecular contour-length predictions of 314.06 ± 9.27 nm. Average single-bond rupture forces of -0.95 ± 0.04 nN were observed at increased contact times. "
10/14/2012 - "The single bond is more vulnerable to rupture than the triple bond and aromatic bond, although it has a shorter bond length (0.19 Å shorter) than the aromatic bond. "

06/01/2016 - "This study tested whether CCMS-HP could be used to form a biomimetic barrier on the exposed dentin for prevention of dentin sensitivity without impairing the bonding of Single Bond Universal (SBU) self-etch adhesive to the dentin. "
01/01/2021 - "A total of 254 patients with moderate to severe dentine hypersensitivity were randomly divided into Group A (Single Bond Universal Agent) and Group B (Seal & Protect Agent) according to the treatment provided. "

04/01/2002 - "In this study, the penetration of three proprietary dentine-bonding agents (Prime & Bond 2.1, Single Bond, Liner Bond 2) and experimental dentine-bonding systems incorporating an antibacterial monomer, 12-methacryloyloxydodecylpyridinium bromide (MDPB), into artificial root caries lesions was evaluated, and the bactericidal activity of each material against Streptococcus mutans or Lactobacillus casei impregnated into demineralized dentine blocks was assessed. "

12/01/2020 - "The samples were stratified into four groups (n = 10) according to the treatment performed; SBU- Adper Single Bond Universal (3M ESPE), SBU_60 - SBU associated with the Nd:YAG laser (60mJ, 10Hz, 0.6W - 47.77 J / cm²), SBU_80 - SBU associated with the Nd:YAG laser (80mJ, 10Hz, 0.8 W - 63.69 J / cm2) and C - dentin without treatment (smear layer). "
10/01/2011 - "However, leakage was observed at dentin margins in two wet with primer systems, All-Bond 2 (1.31 +/- 1.39 mm) and Single-Bond 2 (0.37 +/- 0.28 mm), which required phosphoric etching to remove a weak smear layer on prepared dentin."
01/01/2007 - "Eight groups were pre-treated with EDTA or phosphoric acid to remove the smear layer, followed by a bonding agent (Bond-1 or Single Bond) and resin cement (Rely X or Perma Cem). "
12/01/2007 - "A new smear layer was created and the permeability measured after the crowns were bonded with Single Bond (3M ESPE), One-Up Bond F (Tokuyama), and AdheSE (Ivoclar Vivadent), either according to manufacturer's instructions or after treating the acid-etched dentin with a 3 wt% potassium oxalate gel. "