|1.||Georgiou, George: 2 articles (06/2013 - 11/2010)|
|2.||Wichelhaus, Andrea: 1 article (01/2014)|
|3.||Ilie, Nicoleta: 1 article (01/2014)|
|4.||Rudzki, Ingrid: 1 article (01/2014)|
|5.||Paschos, Ekaterini: 1 article (01/2014)|
|6.||Huth, Karin C: 1 article (01/2014)|
|7.||Lamper, Timea: 1 article (01/2014)|
|8.||BenGassem, Afnan A: 1 article (06/2013)|
|9.||Jones, Steven Peter: 1 article (06/2013)|
|10.||Jones, Steven P: 1 article (11/2010)|
06/01/1999 - "This study investigated time to first failure of stainless steel orthodontic first permanent molar tubes (Ormco Corp) bonded with a light-cured resin adhesive (Transbond) and assessed whether this was related to patient gender, age of the patient at the start of treatment, the presenting malocclusion, or the operator. "
08/01/1998 - "The purpose of this study was to investigate the time to first failure of stainless steel orthodontic brackets (Ormco Corp, Glendora, Calif) bonded with a light-cured resin adhesive (Transbond, 3M Unitek, Monrovia, Calif) and assess whether time to failure was related to the patient's age at the start of treatment or sex, the proficiency of the individual placing the brackets, or the presenting malocclusion. "
|2.||AIDS-Related Complex (ARC)
04/01/2005 - "The aim of this study was to evaluate the degree of conversion (DC) of two lingual retainer adhesives, Transbond Lingual Retainer (TLR) and Light Cure Retainer (LCR), cured with a fast halogen light, a plasma arc light and a light-emitting diode (LED) at various curing times. "
01/01/2014 - "Two different two-component self-etch adhesives (Clearfil SE and Transbond Plus) and two single-component self-etch adhesives (Ideal and iBond) were investigated after using different polymerization procedures (light-emitting diode for 10 or 20 s or plasma arc curing device for 3 or 6 s). "
05/01/2003 - "The plasma arc light produced significantly (P =.006) higher bond strength than did the halogen light or the argon laser when Transbond was used. "
02/01/2006 - "A standard pre-adjusted edgewise premolar bracket (Victory Series) was bonded to each tooth using a light-cured orthodontic adhesive, Transbond X. Group 1 (control) specimens were cured with an Ortholux XT (tungsten-quartz-halogen bulb) light for 20 seconds, group 2 with an Ortho lite (plasma arc) for 6 seconds and group 3 with an Ortholux LED light-emitting diode for 10 seconds. "
06/01/2013 - "The initial bond strength of Transbond Supreme LV was significantly higher than Transbond XT, while the fatigue bond strengths of both resins were comparable. "
06/01/2013 - "No statistically significant difference was found between the fatigue bond strengths of Transbond Supreme LV and Transbond XT (P = 0·323). "
11/01/2010 - "There were no statistically significant differences between the mean initial (unfatigued) and fatigue bond strengths of Transbond XT and Transbond PLUS Color Change under laboratory conditions. "
11/01/2010 - "The fatigue mean shear bond strength for Transbond XT (15.87 MPa) was similar to that of Transbond PLUS Color Change (15.33 MPa), and the difference was not statistically significant (p > 0.999). "
11/01/1992 - "While the thermodebonding of metal brackets worked properly and without any obvious pulp damage, there were problems related to the thermodebonding of ceramic brackets: (1) if more than one heating cycle was necessary, several teeth showed localized damage of the pulp with slight infiltration of inflammatory cells, (2) bracket fractures occurred frequently, and enamel damage could be shown, and (3) often with Transbond (Unitek/3M, Monrovia, Calif.) as the adhesive, more than one heating cycle was necessary for bracket removal, and thus patients complained about pain."
|5.||Dental Caries (White Spot)
|1.||Stainless Steel (Steel, Stainless)